Sign in | English | Terms of Use
DictionaryForumContacts

   English ⇄
Terms for subject Metallurgy containing exit | all forms | exact matches only
EnglishChinese
beam exit hole射线束出口
broad face shell at mold exit结晶器出口处宽面坯壳
die exit angle模孔出口锥角
die exit angle模孔出口锥
electrolyte exit电解液出口
emergency exit安全门
emergency exit太平门
entry and exit equipment进出口料设备
exit angle模孔出口锥
exit angle出口锥
exit aperture出口孔径
exit bridle出口张紧装置
exit bridle roll出口张紧辊
exit bridle roll diameter出口张紧辊直径
exit clamp出口夹持器
exit control引出端控制
exit end出口端
exit end of kiln【团】 窑头
exit end of kiln窑头
exit end of kiln回转窑窑头
exit end of rotary kiln回转窑窑头
exit flue排气烟道
exit gas逸出气体
exit gas排出气体
exit gas废气
exit guide出口导卫板
exit guide and guard出口导卫板
exit guide and guard device出口导卫装置
exit loop puller出口活套拉辊
exit looper【压】 出口活套
exit looper car出口活套车
exit Mach number of nozzle喷嘴出口马赫数
exit nozzle出口喷管
exit nozzle throat出口喷管喉道
exit nozzle throat喷管喉道
exit of deformation zone变形区出口
exit of mold结晶器出口 (If the heat transfer model is used to predict the thickness of the solidified shell, at the exit of the mold, a value of about 10mm would have been obtained. 如果将该传热模型用于预测结晶器出口处的凝固坯壳厚度，那么所得的厚度值约为10 mm。)
exit of radiation射线出口
exit of tundish中间包出口
exit piler出口垛板机
exit plane出口平面
exit port出孔
exit port出口
exit pressure出口压力
exit side输出侧
exit side机后侧
exit side出料侧
exit slit出射缝隙
exit soft reduction cylinder轻压下出口液压缸
exit speed出口速度
exit table【压】 输出辊道
exit table输出辊道
exit temperature出炉温度
exit temperature出口温度
exit tension bridle出口辊式张紧装置
exit thickness出口厚度
exit thickness轧后厚度
exit tube出口管
exit vapour逸出蒸汽
furnace gas exit炉气出口
gas exit气体炉气出口
high exit speed stream高出口速度注流
high exit velocity stream高出口速度注流
kiln exit gas窑尾烟气
longer mold exit长结晶器出口
mold exit结晶器出口
product exit成品出口
product exit产物出口
roasted ore exit焙砂放出口
roasted ore exit焙烧矿出口
safety shell thickness at mold exit结晶器出口安全坯壳厚度
scrap exit废料出口
SEN exit port浸人式水口出钢孔 (Immersion depth is defined as the distance between the meniscus and the top edge of the SEN exit port. 插人深度被定义为金属弯月面至浸人式水口出钢孔上沿的距离。)
shell temperature at mold exit出结晶器坯壳温度
shell thickness at mold exit结晶器出口处坯壳厚度 (【技】即铸坯离开结晶器下口时的坯壳厚度。出结晶器坯壳厚度过薄会因铸坯内钢水静压力的作用而导致薄坯壳漏钢。)
shell thickness at mold exit出结晶器坯壳厚度
steam exit蒸汽出口
three-car exit looper三车式出口活套
tracer concentration at exit of tundish中间包出口示踪剂浓度
tundish exit中间包出口
waste exit废料排出口
waste exit废料出口
wide-face shell at mold exit结晶器出口处宽面坯壳

Get short URL