DictionaryForumContacts

   Chinese
Terms containing 定 位 孔 | all forms | in specified order only
SubjectChineseEnglish
tech.不定位穿孔off-punch
mech.eng.为了安全,在钻孔的同时,台虎钳和夹钳牢牢地固定住工件,防止材料不小心移位For safety reasons, vises and clamps securely hold the work piece as the hole is bored in order to prevent material from shifting unexpectedly
tech.多点照相钻孔定位仪multiple photograph orientation instrument
el.大孔径无线电定位天线阵wide aperture radio location array
tech.套合定位孔register punch
tech.套合定位孔register hole punch
tech.孔定位器hole locator
avia.孔定位样板hole locating template
tech.孔径定位aperture setting
construct.定位工艺gauge hole
auto.定位knock hole
archit.定位工艺gauge hole
transp.定位装配,辅助pilot hole
archit.定位工艺gage hole
gen.定位同步feedhole
construct.定位工艺冲头gauge punch
eng.geol.定位孔spot hole
hydroel.st.定位孔pilot hole
eng.geol.定位孔spacing hole
plast.定位孔register hole
oil定位孔sprocket hole
oil定位孔gauge hole
el.mach.定位孔fixing hole
el.mach.定位孔knock hole
met.定位孔location hole
tech.定位孔locating hole
tech.定位孔index hole
tech.定位孔gage hole
avia.定位导孔coordinated pilot hole
tech.定位工艺孔冲头gauge punch
tech.定位工艺孔冲头gage punch
tech.定位打孔器pilot punch
tech.定位穿孔positional punch
tech.定位钻孔layer position hole
el.定位销和孔dowel pin and socket
polym.定位销孔模具dowel hole
compr.定位销孔dowel hole
tech.定位销孔knock hole
archit.定位锁孔knob hole
tech.定向钻孔方位测量orienting hole survey
tech.定孔位【岩】location of boring
tech.定孔位【岩】location of borehole
tech.定孔位日期date of location
oil射孔器定位器perforator positioner
avia.工装定位基准tooling index holes
tech.打孔定位销栓register stud
avia.标准孔定位样板master hole locating template
textile梳栉半孔定位half-hole position
expl.模式炮孔行间定位策略pattern row orientation strategies
tech.炮孔定位emplacement of borehole
tech.炮孔定位emplacement of blast-hole
expl.炮孔定位与定向positioning and orientation of boreholes
auto.硫化定位孔position fixed hole for vulcanizing
auto.硫化定位孔bottom orifice
expl.装药比、即单位体积的岩石爆破所需的炸药量、根据岩石的类型、炮孔的深度及所用的炸药而定The loading ratio or amount of explosive required per volume of rock to be broken, depends on the type of rock,the depth of the hole,and the explosive to be used
avia.调整片定位孔tab index hole
tech.钻头定位孔collared hole
tech.钻孔定位touching point of bit
eng.geol.钻孔定位location of a drill hole
tech.钻孔定位hole position
tech.钻孔定位attack cut
tech.钻孔定位器hole locator
tech.钻孔定位支架hole director
earth.sc.钻孔定位装置boring fixture
shipb.镗孔前检查轴系中心线定位check center line positioning for shaft system before boring
shipb.镗孔前检查轴系中心线定位check center-line positioning for shaft system before boring
shipb.镗孔前检查轴舵系中心线定位inspecting center line positioning for shaft and rudder system before boring
shipb.镗孔前检查轴舵系中心线定位inspecting center-line positioning for shaft and rudder system before boring
expl.飞石产生的主要原因包括抵抗线不足、炮泥长度不够、钻孔不精确、单位炸药消耗量过多、地质条件不利露天节理、矿层不稳固和空穴、延时定时和序列不当、延时不精确、发生反向爆破、以及台阶上部岩石松散等The major causes of flyrock are inadequate burden, inadequate stemming length, drilling inaccuracy, excessive powder factor,unfavorable geological conditions open joints, weak seams and cavities, inappropriate delay timing and sequence, inaccuracy of delays, back break and loose rock on top of the bench