Chinese | English |
一砖半厚墙 | brick and a half wall |
一等厚锡层镀锡薄钢板 | premier charcoal tinplate |
一般厚锡层镀锡薄钢板 | ordinary charcoal tinplate |
万能式中厚板轧机 | universal plate mill |
万能轧机轧制的齐边中厚钢板 | universal mill plate |
三丝式保护渣层厚度测定法 | three-wire method for measuring thickness of flux layer |
三丝式保护渣层厚度测定法 | flux layer thickness measuring method with three wires |
三辊劳特式中厚钢板轧机 | three-high Lauth plate mill |
三辊式中厚板轧机 | three-high plate mill |
三辊式中厚板轧机机组 | three-high plate mill train |
三辊式中厚板轧机组 | three-high plate mill train |
管壁不加厚 | nonupsetting (的) |
不加厚的 | non upsetting |
不加厚油管 | non-upset tubing |
不同厚度 | dissimilar thickness |
不均厚度 | uneven gauge |
不均匀厚度 | off-gauge |
不等厚角钢 | angle steel with unequal thickness |
不等壁厚异型钢管 | special-shape tube with variable wall thickness |
不等壁厚异型钢管 | special-shape steel pipe with variable wall thickness |
中厚壁管 | medium tube |
中厚壁管 | medium wall pipe |
中厚壁管 | medium-thick wall tube |
中厚板 | heavy and medium plates |
中厚板剪切机 | plate shear |
中厚板剪切机 | plate shears |
中厚板剪切机 | plate cutter |
中厚板厚度 | gauge of plate |
中厚板双边修边剪切机 | double-sided plate trimming shear |
中厚板坯 | medium-thick slab |
中厚板坯连铸机 | medium-thickness slab caster |
中厚板坯连铸机 | intermediate thickness slab caster |
中厚板堆垛机 | plate piler |
中厚板平整机 | plate-levelling machine |
中厚板平整机 | plate-straightening machine |
中厚板平整机 | plate leveller |
中厚板拉伸矫直机 | plate stretcher |
中厚板标志打印台 | plate marking table |
中厚板标志打印辊道 | plate marking table |
中厚板精整 | plate finishing |
中厚板翻转机 | plate turnover |
中厚钢板轧制 | plate rolling |
中厚板轧机 | plate mill |
中厚板轧机 | heavy and medium plate mill |
中厚钢板 | plate steel |
中厚钢板 | plate iron |
中厚黄铜板 | brass plate |
中板和厚板 | plate |
中等厚度内衬 | semithin wall-type inwall |
中等壁厚管 | medium wall pipe |
中等壁厚管 | medium tube |
中等壁厚管 | medium-thick wall tube |
中间包衬厚度 | tundish lining thickness |
临界坯壳厚度 | critical shell thickness (【技】连铸过程中,钢水在连铸机内冷却所形成的连铸坯壳能够有效抵抗钢水压力不致造成破裂漏钢的最低坯壳厚度。它与钢水过热度、结晶器长度、冷却强度、坯型、钢种等因素有关。) |
二丝式保护渣层厚度测定法 | two-wire method for measuring thickness of flux layer (【技】该测定法的原理如下:将钢丝和铜丝固定在钢板上,插人渣层中。由于钢丝熔点低于钢水温度,故钢丝熔化后的长度为整个渣层厚度;铜丝熔点低于液渣层温度,故钢丝熔化后长度和铜丝熔化后长度之差为液渣层厚度。) |
二辊可逆式中厚板轧机 | two-high reversing plate mill |
二辊可逆式中厚板轧机 | two-high reversing-plate mill |
二辊式中厚板轧机 | two-high plate mill |
X光测厚计 | Measuray |
入口厚度 | entry thickness |
全厚烧穿 | melt-thru |
全厚熔透 | melt-thru |
压 内镦厚 | internal upsetting |
内镦厚 | internal upsetting |
切割金属极限厚度 | cutting capacity |
切边中厚板轧机 | sheared plate mill |
切边中厚钢板 | sheared plate |
切过边的中厚钢板 | sheared plate |
初始厚度 | initial thickness (常指轧件的) |
初始厚度 | incoming thickness (常指轧件的) |
剩余炉衬厚度 | remaining lining thickness |
半厚 | half-thickness |
半厚砖 | one-cut brick |
半值厚度 | half-value thickness |
半吸收厚度 | half-value thickness |
单张厚钢板 | discrete steel plate |
厚内衬 | thick wall type inwall |
厚内衬 | thick wall-type inwalls |
厚坯壳 | thick shell |
厚实涂层 | strong coating |
厚层干燥 | volume drying |
厚层泥岩 | argillite |
厚层电镀品 | heavy electroplate |
厚层镀锌 | heavy galvanizing |
厚层阳极化处理 | thick anodizing |
厚带材 | thick strip |
厚带材 | heavy strip |
带材厚度 X 光测量仪 | measuray |
厚度上限 | overgauge limit (薄板的) |
厚度上限 | over-gauge limit |
厚度下限 | undergauge limit (薄板的) |
厚度不合格带材 | off-gauge strip |
厚度不均 | uneven gauge |
厚度不均匀性 | grow-back |
厚度不均性 | grow-back |
厚度公差 | thickness deviation |
厚度公差 | gauge tolerance |
厚度合格 | on-gauge (的) |
厚度同轧辊直径之比 | thickness ratio |
厚度指示器 | thickness indicator |
厚度改变 | gauge changing |
厚度的"T" 控制法 | T-method of gauge control |
厚度范围 | gauge span |
团 厚料层 | thick bed |
团 厚料层 | deep bed |
厚料层 | thick bed |
厚料层 | deep-bed |
厚料层加压过滤 | deep-bed pressure filtration |
厚料层冷却机 | deep bed cooler |
厚料层冷却机 | deep-bed cooler |
厚料层加压过滤 | deep bed pressure filtration |
厚料层操作 | high bed operation |
厚料层操作 | deep bed operation |
厚料层烧结 | sintering with deep bed |
厚料层烧结 | thick-bed sintering |
厚料层烧结 | deep bed sintering (【技】在烧结炉算上保持较高的铺料厚度进行烧结的铁矿石烧结工艺。该工艺能有效地改善烧结矿质量:提高烧结矿机械强度、减少粉末量、降低氧化亚铁含量、改善还原性能。) |
厚料层烧结法 | high bed sintering |
厚料层试验 | deep bed test |
厚料层试验 | deep-bed test |
厚料层高度 | deep bed height |
厚板 | massive plate |
厚板 | thick plate |
厚钢板 | heavy steel plate |
厚钢板 | thick steel plate |
厚钢板 | steel plate |
厚钢板 | rough plate |
压 厚钢板 | plate |
厚钢板 | massive plate |
厚钢板 | iron plate |
厚钢板 | heavy plate |
厚板切断冲裁冲头 | quill punch |
厚板剪切机 | heavy plate shearing machine |
厚板剪切机 | heavy plate shear |
厚板双边剪切机 | double-side plate trimming shear |
厚板坯连铸机 | thick slab caster |
厚板坯连铸机 | continuous thick slab caster |
厚板坯钢铁联合生产厂 | thick slab integrated steel producer |
厚板堆垛机 | plate piler |
厚板拉延矫直机 | plate stretcher |
厚板桩 | plank pile |
厚板焊接 | plate welding |
厚板矫正机 | heavy plate straightener |
厚板矫直机 | plate straightener |
厚板矫直机 | plate straightening machine |
厚板矫直机 | plate mangle |
厚板矫直机 | heavy plate straightener |
厚板轧制 | heavy plate rolling |
厚板轧机 | plate mill (The first phase of the integrated steel plant included a blast furnace, an oxygen converter, a battery of coke ovens, a slab mill, a plate mill, a billet mill, and a hot-strip mill, and was completed in 1973.这座钢铁联合钢厂的一期工程包括一座高炉、一座氧气转炉、一组焦炉、一台板坯轧机、一台厚板轧机、一台小方坯轧机和一台带钢热轧机,于1973 年完工。) |
厚板轧机 | heavy plate mill |
厚氧化皮的生成 | heavy scale formation |
厚氧化铁皮 | heavy scale |
厚渗碳层 | heavy case (大于 0.06in 的渗碳层) |
厚渣 | thick slag |
连 厚渣圈 | thick flux rim |
厚渣层 | thick slag |
厚膜 | heavy film |
厚膜涂层 | thick-film coating |
厚膜润滑 | thick-film lubrication |
厚膜润滑 | full film lubrication |
厚膜电路 | thick-film circuit |
厚膜覆层 | thick-film coating |
厚药皮焊条 | heavily covered electrode |
厚药皮焊条 | heavily coated electrode |
厚薄间隙规 | thickness piece |
厚薄不均引起的裂纹 | bull crack |
厚薄不均而引起的裂纹 | bull crack |
厚薄规 | thickness indicator |
厚薄规 | thickness gauge |
厚薄规 | feeler |
厚表面层 | deep case |
厚钢板 | iron plate |
厚钢板 | coarse plate |
厚钢板质量波动 | fluctuation in steel plate quality |
厚锌层镀锌薄钢板 | heavy iron |
厚锡层"碳炼"镀锡薄钢板 | charcoal tin- plate |
厚锡层镀锡薄钢板 | charcoal tin-plate |
厚镀层 | heavy coating |
厚镀锌薄钢板 | heavy galvanized steel sheet |
同位素测厚仪 | isotope thickness measuring instrument |
同位素测厚仪 | isotope gauge |
同位素测厚仪 | nucleonic thickness gauge |
同位素测厚仪 | isotopic thickness gauge (【技】由放射源、检测器和指示器等组成的一种测厚仪器。当片状待测物从放射源和检测器之间通过时,由于不同质量和厚度的物质对辐射线的阻挡程度不同,从而即可确定被测物质的厚度。) |
器壁厚度 | wall thickness |
均厚坯壳 | uniform strand shell |
均厚板坯 | uniform thickness slab |
均厚板坯 | uniform gauge slab |
均厚钢坯壳 | uniform steel shell |
均匀厚度 | uniform gauge |
坯壳厚区 | thick zone of shell |
坯壳厚区 | thick region of shell |
坯壳厚度 | thickness of shell |
坯壳厚度 | shell thickness |
连 坯壳厚度测量 | measure of shell thickness |
坯壳的计算厚度 | calculated shell thickness |
坯壳临界厚度 | critical shell thickness |
坯壳周边厚度 | shell thickness over whole circumference |
坯壳实测厚度 | measured shell thickness |
复合层厚度比 | cladding ratio |
外加厚 | external-upset |
外加厚油管 | external-upset tubing |
外层厚度 | outer layer thickness |
多倍厚板 | thick iron |
多倍厚板 | multiples |
大厚度 | heavy gauge |
板材的大厚度、大尺寸 | heavy gauge |
大厚度渣层 | thick slag |
安全坯壳厚度 | safety shell thickness (【技】连铸坯出结晶器后能有效抵抗钢水静压力,不致于因坯壳过薄而导致漏钢。) |
γ 射线厚度仪 | γ-ray thickness gauge |
β 射线厚度计 | β-ray thickness gauge |
γ 射线测厚仪 | gamma-ray thickness recorder |
γ射线测厚仪 | gamma gauge |
β 射线测厚仪 | beta thickness gauge |
β 射线测厚仪 | β-gauge |
γ射线测厚仪 | gamma-ray thickness recorder |
β射线测厚仪 | 0-gauge |
γ射线测厚仪 | gamma thickness gauge |
β射线测厚仪 | beta thickness gauge |
X 射线测厚仪 | X-ray gauge |
γ 射线测厚仪 | γ-ray thickness gauge |
γ 射线测厚仪 | gamma thickness gauge |
X 射线测厚仪 | X-ray thickness gauge |
X 射线管壁厚度测量仪 | X-ray pipe-wall gauge |
X 射线锡层测厚仪 | X-ray tin coating thickness gauge |
板材的小厚度 | light gauge |
小厚度板材纵剪作业线 | light slitter line |
小厚度板材纵剪作业线 | light slitter line |
布料厚度 | charging thickness |
布料厚度 | charging level |
带材厚度 | strip thickness |
带材厚度X光测微计 | Measuray |
带材厚度公差 | strip thickness tolerance |
带材厚度压下螺丝控制系统 | gaugemeter-screw system |
带材厚度同轧辊直径之比 | thickness ratio |
带材厚度差 | strip thickness difference |
带材厚度差 | grow-back |
带材厚度张力控制系统 | gaugemeter-tension system |
带材厚度的压下螺丝控制系统 | gaugemeter-screw system |
带材厚度的张力控制系统 | gaugemeter-tension system |
带材合格厚度 | target strip thickness |
带材测厚仪 | strip thickness gauge |
压 带材的厚度差 | grow-back |
带材轧制厚度自动控制 | course gauge control |
带材轧制中厚度的控制 | course gauge control |
带钢厚度 | thickness of strip (The loading of the rolls, the adjustments for controlling the thickness of the strip, the lubrication, the mechanism which directs the metal from one stand or mill train to the next, must be controlled automatically. 轧辊负荷、带钢厚度控制调整、轧机的润滑、轧件由一个机架或一个轧机机组到下一个机架或下一个轧机机组的导向机构等,都必须进行自动控制。) |
带钢厚度 | steel strip thickness |
带钢厚度 | strip thickness |
带钢厚度偏差 | strip thickness deviation |
带钢厚度弹性后效 | spring-back of strip thickness |
带钢厚度精度 | strip thickness accuracy |
带钢厚度精度 | steel strip thickness accuracy |
带钢中部厚度 | thickness in middle of strip |
带钢初始厚度 | initial height of strip |
带钢母板厚度 | starting strip thickness |
带钢轧前厚度 | ingoing gauge of strip |
带钢轧前厚度 | incoming thickness of strip |
异形厚板 | sketch plate |
强度减半厚度 | half-value thickness |
急冷层厚度 | depth of chill |
恒定液渣层厚度 | constant liquid slag layer thickness |
成品板材厚度 | finished plate thickness (Of the slabs not continuously cast, 74 percent is not produced with continuous casting process because of limits in finished plate thickness and weight, and 22 percent is because of limits in casting excessively small lot sizes. 在非连铸生产的板坯中,由于受成品板材厚度和重量限制而不能用连铸方法生产的占74%,由于受连铸批量太小限制而不能用连铸方法生产的占22%。) |
放射性元素测厚仪 | radiation thickness gauge |
放射性同位素测厚仪 | radioisotope thickness gauge |
放射测厚法 | radiographic thickness gauging |
数字式超声波测厚仪 | digital ultrasonic thickness gauge |
料层厚度 | height of layer |
料层厚度 | bed height |
料层厚度 | bed thickness |
料层厚度 | height of bed |
料层厚度 | depth of charge |
料层厚度 | charging level |
料层厚度 | layer height |
料层厚度 | pellet-bed depth |
料层厚度 | mix thickness |
料层厚度 | bed depth |
料层厚度指示器 | bed height indicator |
料层厚度控制 | charge thickness control |
团料层厚度控制 | control of bed height |
团料层厚度控制 | charging level control |
料层厚度控制 | bed height control |
料层厚度控制 | charging level control |
料层厚度控制 | bed level control |
料层厚度极限 | bed height limit |
料层厚度测量 | bed height measurement |
铁料层厚度的径向变化 | radial variation in thickness of layer |
普通厚锡层镀锡薄钢板 | common charcoal tinplate |
最优厚锡层镀锡薄钢板 | best charcoal tin plate |
最低可轧厚度 | lower thickness limit in rolling |
最低坯壳厚度 | minimum shell thickness (The breakout probability is inversely proportional to the minimum shell thickness at the mold exit and is directly proportional to the temperature of liquid steel. 漏钢概率与结晶器出口处最低坯壳厚度成反比,与钢水温度成正比。) |
最低壁厚 | minimum wall thickness |
最大厚度直径 | maximum gauge |
最大厚度 | maximum gauge (板、带材等的) |
最大焊缝厚度 | maximum throat depth |
最小厚度 | minimum gauge (板、带材的) |
板材的最小厚度 | minimum gauge |
最小可轧厚度 | minimum thickness for rolling |
最小可轧厚度 | minimum gauge in rolling |
有效炉壁厚度 | effective furnace wall thickness |
有效焊接厚度 | effective throat thickness |
有缺陷的厚锌层钢板 | heavy iron (因锌槽中含铁过多而导致锌花不正常的缺陷钢板) |
未经热处理的热轧厚板 | green plate |
来料厚度 | incoming thickness |
来料轧前厚度 | incoming thickness |
钢板厚度 | plate thickness |
板坯厚度 | thickness of slab |
板坯厚度 | slab thickness |
板坯测厚 | thickness measurement of slab |
板坯测厚 | slab thickness measurement |
压 板带材中心凸厚部分 | crown |
压板带材中心部分增厚 | crowning |
板、带材中心部分增厚 | crowning |
板材厚度同轧辊直径之比 | thickness ratio |
核测厚仪 | nuclear gauge |
核辐射测厚仪 | nuclear radiation gauge |
根部面厚度 | thickness of root face |
横向厚度波动值 | lateral gauge variation |
横向厚度波动值 | lateral gauge variation (轧件的) |
轧件横向厚度波动值 | lateral gauge variation |
气刀镀层厚度控制装置 | vapour die coating thickness control unit |
浇铸的带钢厚度 | cast strip thickness (The capacity of twin-roll caster increases with the reduction of cast strip thickness because the contact length from the meniscus to the "kissing point" remains unchanged. 由于从金属弯月面到"吻点"的接触长度保持不变,因此双辊连铸机的生产能力随浇铸带钢厚度减薄而增加。(此处"吻点"指的是双辊连铸机两个旋转辊表面距离最近的点)。) |
测厚仪 | pachymeter |
测厚仪 | gaugemeter |
测厚仪 | pachometer |
测厚仪 | thickness gauge |
测厚仪 | thickness tester |
测厚仪 | calibrator |
测厚装置 | thickness measuring device |
测厚装置 | gauging device |
测厚规 | finger gauge |
测厚计 | thickness indicator |
测厚计 仪 | gaugemeter |
测厚计 仪 | pachymeter |
测厚计 仪 | thickness gauge |
测厚计 仪 | thickness indicator |
测厚计 仪 | thickness tester |
测厚计 仪 | thickness measuring instrument |
测厚计 仪 | pachometer |
测厚计 | pachymeter |
测厚计 | pachometer |
测厚辊 | thickness measuring roll |
测厚辊 | gauging roll |
测量炉底厚度 | measuring bottom thickness |
测量炉底厚度 | furnace bottom thickness measurement |
浸人式水口壁厚 | wall thickness of submerged entry nozzle |
浸人式水口壁厚 | submerged entry nozzle wall thickness |
浸人式水口壁厚度 | SEN wall thickness |
涂层厚度 | layer thickness |
涂层厚度测量仪 | layer thickness meter |
涂层厚度控制 | coating thickness control |
涂层厚度测量仪 | layer thickness meter |
涂层厚度测量仪 | coating thickness gauge |
涂层厚度称量测定法 | weight-of-coating test |
涂层厚度调节辊 | metering roll |
渗氮层厚度 | depth of nitration |
钢的渗碳层厚度 | depth of case |
渗碳层厚度 | depth of case |
渗碳层厚度 | case depth |
渣厚测量 | slag thickness measurement |
渣厚测量系统 | slag thickness measuring system |
渣圈厚度 | thickness of slag rim |
渣圈厚度 | rim thickness |
渣层厚度 | slag thickness |
渣层厚度 | thickness of slag layer |
渣层厚度 | slag layer thickness |
渣层厚度 | slag depth |
渣层厚度传感器 | slag depth sensor (In an alternative technique that does not require two measurements, the slag depth sensor developed at LTV is mounted on the lance that permits the simultaneous measurement of steel oxygen activity and temperature. 另一项技术是(美国) LTV 钢铁公司研发的渣层厚度传感器,它不需要进行两次测量。将其安装在探测枪上,在测量钢水温度和氧活度的同时,测量渣层厚度。) |
渣层厚度测量仪 | slag depth measuring meter |
渣层厚度测量系统 | slag depth measuring system |
漆层厚度计 | painting film thickness meter |
漏钢坯壳厚度 | breakout shell thickness |
炉衬厚度 | line thickness |
炉衬厚度 | thickness of furnace lining |
炉衬厚度 | thickness of lining |
炉衬厚度 | lining thickness |
炉衬厚度 | liner thickness |
炉衬初始厚度 | starting lining thickness |
炉衬原厚 | original thickness of furnace lining |
炉衬残厚 | residual lining thickness |
炉衬残厚 | remaining lining thickness |
焊喉厚度 | throat thickness |
焊缝厚度 | throat thickness |
焊缝厚度 | throat depth |
焊缝实际厚度 | actual throat |
焊缝计算厚度 | effective throat thickness |
焦窗厚度 | coke slit thickness (【技】汉语中的"窗"通常是不涉及厚度的。但炼铁专业中的"焦窗"是一种特殊的"窗",即高炉软熔带焦炭夹层所形成的供煤气在高炉中通过的"透气窗",故其厚度就是高炉软熔带焦炭夹层 (coke layer) 的厚度。: The cohesive zone shape, elevation and coke slit thickness are determined by the charging practice, the ore/coke ratio (or the coke rate), and the softening and melting temperatures of the ferrous materials. 软熔带的形状、高度以及焦窗厚度取决于装料实践、矿焦比(或焦比)和含铁炉料的软化和熔化温度。) |
熔渣厚度测量 | slag thickness measurement |
特厚板轧机 | ultraheavy plate mill |
特厚钢板 | ultraheavy steel plate |
特制厚锡层镀锡薄钢板 | special charcoal tinplate |
特强厚壁管 | double strength pipe |
球团料层厚度 | depth of pellet bed |
球层厚度 | pellet-bed thickness |
球层厚度 | pellet-bed depth |
理想液渣膜厚度 | ideal liquid slag film thickness |
生球团层厚 | green ball depth |
电子测厚仪 | electronic thickness gauge |
电测厚度仪 | electrical thickness gauge |
电测厚度仪 | electric thickness gauge |
电测厚度计 | electric thickness gauge |
砌砖厚度 | brickwork thickness |
硬厚纸板 | card-board |
窄厚扁钢 | bar of flat |
等厚镀层 | equal thickness coating |
等厚镀层电镀锡板 | equally coated electrolytic tinplate |
等壁厚异型钢管 | special-shape steel tube with identical wall thickness |
等壁厚异型钢管 | special-shape steel pipe with identical wall thickness |
粗轧机用伽马射线测厚仪 | gamma-ray thickness gauge for rougher |
粗轧机用γ射线测厚仪 | gamma-ray thickness gauge for rougher |
罗克内尔式大口径管材壁厚减薄用轧机 | Roeckner tube rolling mill |
脱碳厚度 | decarburisation depth |
腰边镦厚机 | web edge upsetter |
腰部厚度 | web thickness |
腹厚减薄的轧制 | web thickness decrease rolling (【技】一种与连铸工字梁坯相配套的减薄腹厚的轧制方法。) |
腹厚减薄的轧制 | rolling for decreasing web thickness (一种与连铸工字梁坯配套的轧制方法) |
腹板厚度 | web thickness (工字钢的) |
腹板镦厚机 | web edge upsetter |
般厚锡层镀锡薄钢板 | ordinary charcoal tinplate |
荒管壁厚 | shell thickness |
荧光 X 射线测厚仪 | fluorescence X-ray thickness gauge |
荧光X射线测厚仪 | fluorescence X-ray thickness gauge |
薄板厚度 | sheet gauge |
薄板厚度 | gauge of sheet |
薄板厚度卡规 | sheet thickness gauge |
薄板厚度范围 | range of sheet thickness |
薄板测厚仪 | sheet thickness gauge |
薄板测厚仪 | sheet thickness calibrator |
薄板测厚计 | sheet thickness gauge |
薄钢板标准厚度 | standard thickness of steel sheet |
薄钢板标准厚度 | standard sheet metal gauge |
表盘式测厚仪 | dial thickness gauge |
表盘式薄板测厚仪 | dial sheet gauge |
衬里厚度 | lining thickness |
衬里厚度 | liner thickness |
西屋X 射线厚度计 | Westinghouse thickness gauge |
西屋 X 射线厚度计 | Westinghouse thickness gauge |
调液厚器 | absorptiometer |
超声厚度仪 | sonigauge |
超声厚度计 | sonizon |
超声波测厚仪 | ultrasonic thickness gauge |
超声波测厚仪 | supersonic thickness gauge |
超声波测厚计 | reflectogauge |
超声波金属厚度测定仪 | sonigauge |
超声测厚仪 | sonigauge |
轧件厚度 | height of rolled material |
轧件厚度 T 控制法 | T-method of gauge control (采用张力变动的方法) |
轧件出口厚度 | delivery stock thickness |
轧件出口厚度 | delivery rolled material thickness |
轧件初始厚度 | initial rolled material thickness |
轧件初始厚度 | initial rolled piece thickness |
轧件初始厚度 | initial material thickness |
轧件平均厚度 | mean height of material |
轧件平均厚度 | average workpiece thickness |
轧件的平均厚度 | mean workpiece thickness |
轧件轧前厚度 | initial thickness of rolling material |
轧件轧前厚度 | initial stock height |
压轧制带材厚度指示仪 | readout |
轧前厚度 | incoming thickness |
轧前厚度 | ingoing gauge |
轧前厚度 | ingoing thickness |
轧前厚度 | entry thickness |
轧后厚度 | delivery stock thickness |
轧后厚度 | delivery thickness |
轧后厚度 | exit thickness |
轧后厚度 | outgoing gauge |
轧后厚度 | outgoing thickness |
轧后厚度 | delivery material thickness |
轧后厚度 | delivery stock height |
轧机测厚仪 | rolling mill gauge |
轧材出口厚度 | outgoing thickness of rolled product |
轮辐厚度 | web thickness |
软熔带厚度 | thickness of cohesive zone (【技】软熔带厚度增加意味着矿石批重加大,虽因焦窗厚度相应增加使煤气通道的阻力减小,但焦窗数目减少,而且由于扩大矿批后块状带中分布到中心部分的矿石增加,煤气阻力呈增加趋势,从而使总的煤气阻力和总压差可能升高,不利于高炉强化冶炼和顺行。只有适当的焦层和矿层厚度才能使总阻力最小。) |
辊式测厚仪 | roll thickness gauge |
V射线透射测厚仪 | penetron |
锌层厚度电磁波测定法 | electromagnetic testing for zinc coating |
锌层厚度的电磁波测定 | electromagnetic testing for zinc coating thickness |
锌板厚度 | zinc gauge |
锌板厚度规 | zinc gauge |
镀层厚度 | plating thickness |
镀层涂层厚度 | coating thickness |
镀层厚度检验 | coating thickness inspection |
镀层厚度检验 | plating-thickness inspection |
镀层厚度测量仪 | coating thickness meter |
镀层厚度测量仪 | coating thickness gauge |
镀层覆层厚度测量仪 | coating thickness gauge |
镀层测厚仪 | coating thickness gauge |
镀覆厚度 | plating thickness |
镀锌层厚度控制 | galvanized coating thickness control |
镀锌层测厚仪 | zinc coat thickness gauge |
镀锌薄钢板厚度号规 | galvanized sheet gage |
镀锡层厚度磁性测量计 | stannometer |
镉镀层厚度 | thickness of cadmium plate |
镦厚机 | upsetting machine |
镦厚机 | upsetter |
非均厚坯壳 | nonuniform thickness shell |
非接触式 X 射线测厚仪 | X-ray noncontact thickness gauge |
非接触式测厚仪 | non-contact thickness gauge |
非接触式X线测厚仪 | X-ray noncontact thickness gauge |
顶弯区坯壳厚度 | shell thickness at bending zone |
齐边中厚钢板 | universal mill plate (万能轧机轧制的) |
万能轧机轧制的齐边中厚钢板 | universal mill plate |
破碎机齿片厚度 | breaker arm width |