English | Chinese |
binding post | 接线端子 |
binding post | 接线柱 |
bumping post | 车挡 |
bumping post | 缓冲器 |
centre post type thickener | 中心传动式浓缩机 |
CO post combustion | CO 二次燃烧 (These methods for increasing the quantity of scrap charged to the BOF converter include the preheating of scrap, the combustion of carbonaceous fuels, the oxidation of aluminum scrap, and CO post combustion. 这些增加氧气顶吹转炉废钢加人量的方法包括废钢预热、碳质燃料燃烧、废铝氧化以及一氧化碳二次燃烧等。) |
CO post combustion | 一氧化碳二次燃烧 |
control of post-combustion oxygen injection | 【钢】 二次燃烧喷氧控制 |
control post | 操纵台 |
control post | 操纵台站 |
control post | 控制台站 |
degree of post-combustion | 【钢】 二次燃烧率 |
die set guide post | 模具导柱 |
distance-post | 里程标 |
divided post nut | 水压机立柱用对开式螺母 |
effect of post-combustion on energy consumption | 【钢】二次燃烧对能耗的影响 |
effect of post-combustion on furnace performance | 【钢】二次燃烧对炉况的影响 |
engagement system for technical post | 技术职务聘任制 |
four post blast furnace | 四柱悬挂式高炉 |
four-post blast furnace | 四柱悬挂式高炉 |
four post hydraulic press | 四柱式水压机 |
four-post structure | 四斜柱钢结构 (高炉的) |
furnace off-gas post-combustion | 炉子废气二次燃烧 |
guide post | 路标 |
guide post | 导柱 |
heat transfer efficiency of post-combustion | 【钢】 二次燃烧的传热效率 |
high post combustion ratio | 高二次燃烧率 |
housing post | 机架立柱 |
housing post | 牌坊立柱 |
housing post recess | 牌坊立柱凹槽 |
increasing post-combustion ratio | 提高二次燃烧比 |
ingoing control post | 进口侧操作台 |
ingoing control post | 【压】 轧机前操作台 |
ingoing control post | 机前操纵台 |
mill post | 轧机牌坊 |
mill post | 轧机牌坊立柱 |
non post-combustion heats | 非二次燃烧的炉次 |
outgoing control post | 出口侧操纵台 (轧机后的) |
outgoing control post | 出口侧机后操纵台 |
post-acceleration gun | 后加速电子枪 |
post and beam construction | 梁柱结构 |
post and beam construction | 骨架结构 |
post annealing | 后退火 |
post annealing | 焊后在线退火 |
post annealing | 焊缝的焊后退火 |
post argon-blowing stirring | 【钢】 后吹氩气搅拌 |
post breakout measurement of taper | 漏钢后锥度测定 |
post-cleaning | 后清理 |
post-cleaning | 穿透检验验后清洗 |
post combust | 后燃烧 (The carbon monoxide is post combusted with oxygen from the lance. 一氧化碳与氧枪喷出的氧气产生二次燃烧。) |
post combust | 【钢】 二次燃烧 |
post combustion | 【钢】 二次燃烧 |
post combustion | 后燃烧 (【技】通过向炼钢电弧炉或转炉熔池上方含有大量 CO 的空间喷吹氧气,使炉内的 CO 燃烧转变成 CO₂, 同时放出大量的燃烧热。这种吹氧助燃的炼钢工艺为二次燃烧。二次燃烧可节约冶炼成本、加快熔炼进程、提高生产效率。: Post combustion (the further oxidation of CO to CO₂ within the electric arc furnace) is very attractive because it represents a cheap, readily available source of energy. 由于二次燃烧(在电弧炉内将 CO 进一步氧化成 CO₂) 代表了一种廉价、易得的能源,因而它极具吸引力。) |
post-combustion | 二次燃烧 |
post combustion degree | 二次燃烧率 |
post-combustion degree | 二次燃烧率 |
post-combustion in EAF | 电弧炉二次燃烧 |
post-combustion in electric arc furnace | 电弧炉二次燃烧 |
post-combustion lance | 二次燃烧喷枪 |
post-combustion lance | 二次燃烧氧枪 |
post-combustion of CO | CO 二次燃烧 |
post-combustion of converter gas | 转炉煤气二次燃烧 |
post-combustion of converter off-gas | 转炉炉气二次燃烧 |
post-combustion of furnace off-gas | 炉子废气二次燃烧 |
post-combustion operation | 二次燃烧操作 |
post-combustion oxygen | 二次燃烧用氧 |
post-combustion practice | 二次燃烧实践 |
post-combustion technology | 二次燃烧技术 (Because post-combustion technology is used, the EAF oxygen consumption increases from 26 Nm³/tonne to 42 Nm³/ tonne, and the corresponding power consumption is 315 kWh/tonne with a tap-to-tap time of 48 minutes. 由于采用了二次燃烧技术,该电弧炉用氧量由 26 Nm³/t 提高到 42 Nm³/t, 相应的用电量为315 kWh/t, 出钢到出钢时间为 48min。) |
post-drying of slag | 炉渣返干 (【技】炉渣返干发生在转炉吹炼中期,指已经熔化或部分熔化的炉渣出现变稠甚至结成大块的现象。在转炉熔池中碳激烈氧化的吹炼中期,炉渣中 TFe 含量低,导致炉渣中高熔点的 2CaO ・ SiO₂ 和 MgO 等矿物的析出,炉渣熔点升高,变黏变稠,影响熔池反应和成渣过程的正常进行,不能及时形成高碱度炉渣。返干现象严重时,会恶化吹炼过程,降低去硫、去磷效率。) |
post-elastic behaviour | 弹性后效 |
post-emulsification | 后乳化作用 |
post-emulsification fluorescent process | 后乳化荧光探伤法 |
post-emulsification fluorescent process | 后乳化荧光探伤法 |
post-emulsification method | 后乳化渗透检验法 |
post-forging operation | 锻后工序 |
post-forging treatment | 锻后处理 |
post former | 后变形器 (钢丝绳的) |
post-former | 后变形器 |
post forming | 后续成形 (冲压加工后薄板的) |
post-heater | 二次点火器 |
post heater | 保温段 |
post heater | 【团】 二次点火器 |
post-heater | 保温段 |
post heating | 二次加热 |
post heating | 补充加热 |
post heating | 回热 |
post-ignition | 二次点火 |
post-ignition hood | 【团】 二次点火器 |
post-ignition hood | 保温段 |
post-ignition hood | 二次点火器 |
post-ignition suction | 点火后负压 |
post-injection | 后喷 |
post-injection | 后喷吹 |
post-injection process | 后喷工艺 |
post-leaching | 补充浸出 |
post-leaching | 浸出后阶段 |
post-leaching operation | 浸出后处理 |
post-leaching treatment | 浸出后处理 |
post-precipitation | 后沉淀作用 |
post-processing | 后加工 |
post-processing | 二次加工 |
post-processing | 后期处理 |
post-processing | 后部工艺 |
post-reaction heating | 反应后加热 |
post-sale service | 售后服务 |
post-sintering treatment | 烧结后处理 |
post-solidification cooling rate | 凝固后冷却速度 |
post-stirring | 【钢】后搅拌 |
post-stirring with argon | 后吹氩气搅拌 |
post-stirring with argon | 【钢】 氩气后搅拌 |
post stress | 轧机牌坊的立柱应力 |
post stress | 轧机牌坊立柱应力 |
post-stressed | 后张的 |
post-stressed | 后加应力的 |
post-stressing | 后加应力 |
post tempering | 补充回火 |
post tempering | 后回火 |
post-tensioned cable | 后张钢丝绳 |
post-tensioned concrete | 后张法预应力混凝土 |
post-tensioned prestressing | 后张法预应力 |
post-thickener | 后增稠器 |
post-treatment | 后处理 |
post-treatment finishing | 后续精整处理 (During laser hardening treatment heat is concentrated intensely at the surface, little distortion takes place-which means that minimal post-treatment finishing is required. 激光硬化处理时,热量高度集中于表面,工件变形量很小,这就意味着所需要的后续精整处理量也很小。) |
post-weld cleaning | 焊后清理 |
post-weld heat treatment | 焊后热处理 |
post-weld interval | 焊后冷却时间 |
post-weld upsetting | 焊后顶锻 |
post-yield fracture mechanics | 屈服后断裂力学 |
potential for post-combustion | 二次燃烧的潜力 (The results of tests with and without post-combustion substantiate the potential for post-combustion in the electric arc furnace. 使用和未使用二次燃烧的试验结果证实了电弧炉二次燃烧的潜力。) |
potential for post-combustion in EAF | 电弧炉二次燃烧的潜力 |
potential of post-combustion | 二次燃烧的潜力 |
professional-technical post | 专业技术职务 |
queen post | 双柱架 |
queen post | 双柱式 |
system of fixed number of employees and fixed posts | 员定岗制 |